Druz Toolz

Druz Toolz Larry Light  is a pocket ding board and search light.  This light is perfect to get into small, odd places that you may have had trouble with a full size light.  It has a magnet with rotating clip. It fits well in any tool kit and makes finding a lost screw in an interior a breeze.  It currently comes in Red or Yellow.

The Grab Bar is a new leverage point for windows. It is 16 inches long 1 inch diameter and has about 13 inches of work space. Hang this in between the door and the roof weather seal. Place it once and you will not have to move it like a window ring till you are finished with the section of the roof. Get two for a sedan and speed up your pace on a roof buy not having to readjust leverage points. The grab bar now comes with removable pins so the straps can be removed or replaced if needed. The pins pull out by screwing one of your tips into it. Once the pins are pulled you can reverse the straps to use it as a smooth bar or a bar with the scallops.

It comes with two straps, one bar, two delrin pins, and two aluminum pins.

NO TIPS COME WITH THIS.

Druz Slide Hammer was introduced at the 2012 MTE as a show special. The MTE version had a polished aluminum head and a show price, the show special is over. This one has Stainless steel slide and weights with a machined/brushed finish aluminum head that grips all glue tabs, even the new atlas ones. This slider has an internal slider to reduce finger pinch. It has rubber internal dampeners to cushion the impact and give a better pull instead of a hard snap when glue pulling. The length of travel in the slide is 3 1/2 inches, but glue pulling works from the weight impact not the length of travel. The length is 8 3/4 inches without any weights and 14 inches with the heavy weight and extended. The weight changes depending on your preference. The Slide Hammer comes with both small and large weight. The lightest is 1lb 14oz (854g) with the small weight it is 2lb 4 oz (1003g) and with the large weight it is 3lbs 2oz (1422g).

Druz Toolz-These Carbon Fiber Knock Down have an aluminum strike plate and 6lb magnet

Druz Toolz-The abbreviation for Titanium is Ti. The Ti-tack is a very sharp tip for very precise pushing or to push through the nasty sound deadening that is being sprayed on roofs. The Ti-tacks have a lock hole at the base so you can put a smaller tool through it and tighten it down so it will not come loose. The Ti-tack  weighs .17oz/ 5gr. The anodizing on Titanium will change colors with body oils and is only a couple microns thick. It will wear off over time, or with rough treatment. 

Druz Toolz Ti-ce Tack is a shorter version of the Ti-ce Pick, but it is longer than the Ti-tack. Very sharp Titanium with a lock hole through the side.

Druz Toolz-The abbreviation for Titanium is Ti. This is a Titanium version of the Ice Pick, hence the name Ti-ce pick. Like the stainless steel Ice Pick, but lighter, stronger and cooler. The Ti-ce pick has a lock hole at the base so you can put a smaller tool through it and tighten it down so it will not come loose. The Ti-ce pick weighs .6oz/ 18gr. The anodizing on Titanium will change colors with body oils and is only a couple microns thick. It will wear off over time, or with rough treatment.

Druz ToolzThe “17” is a new modular blending hammer. The handle width is available in two different thicknesses.  There is a cross hole for a strike plate so the side can be used to strike a knockdown. The aluminum head has stainless steel threads for long lasting life.  The head and handle are Fused to the carbon shaft.   The 17″ does not come with tips or strike plate.The “17” comes in Red, Blue, or Black currently. 

Druz Toolz-This ice pick tip is 3 inches long and the thin part is 1/4 inch in diameter. This is my everyday tip for fixing hail.

Same great Blending hammer with the extra option of a second screw on tip. This The Double Sided Blending Hammer has the same great balance as the original Mesquite wood hammer.is a hammer only and no tips are included.

 

This Carbon Fiber Blending Hammer is very strong and extremely light. The Double Sided Blending Hammer has the same great balance as the original Mesquite wood hammer. It is threaded for multi-weighted tips that are interchangeable. This thread the industry standard DC tips. By alternating the tips you can adjust the weight of the hammer from 2.2oz/ 62 g without tip to a heavier weight with a second screw on tip. It is very well balanced with an ergonomic handle that rolls well in the palm of your hand. The carbon fiber blending hammer is my every day use hammer. The carbon handle is made of multi directional and multi layered carbon fiber. The handles are hand laid carbon and built in the United States of America.

This Wooden Handle Double Sided Blending Hammer is made of laminated birch wood from Gunstock wood. It is a 12″ hammer with a double sided hammer head. Each hand shaped handle each has its own uniqueness. The head is the same as on the carbon fiber double hammers. There is a limited number of each color.  This hammer is sold without tips.

Druz Tools Doble Sided Blending Hammer

Same great Blending hammer with the extra option of a second screw on tip. This The Double Sided Blending Hammer has the same great balance as the original Mesquite wood hammer.is a hammer only and no tips are included.

This Carbon Fiber Blending Hammer is very strong and extremely light. The Double Sided Blending Hammer has the same great balance as the original Mesquite wood hammer. It is threaded for multi-weighted tips that are interchangeable. This thread the industry standard DC tips. By alternating the tips you can adjust the weight of the hammer from 2.2oz/ 62 g without tip to a heavier weight with a second screw on tip. It is very well balanced with an ergonomic handle that rolls well in the palm of your hand. The carbon fiber blending hammer is my every day use hammer. The carbon handle is made of multi directional and multi layered carbon fiber. The handles are hand laid carbon and built in the United States of America.